Electronic eye sensor watches out for glaucoma
Researchers have designed a high-tech, low-power sensor that can be placed permanently in a person’s eye to track hard-to-measure changes in pressure and monitor for diseases like glaucoma.
The sensor would be embedded with an artificial lens during cataract surgery and would detect pressure changes instantaneously, then transmit the data wirelessly using radio frequency waves.
“No one has ever put electronics inside the lens of the eye, so this is a little more radical,” says Karl Böhringer, professor of electrical engineering at University of Washington. “We have shown this is possible in principle. If you can fit this sensor device into an intraocular lens implant during cataract surgery, it won’t require any further surgery for patients.”
“We want every surgeon who does cataract surgeries to be able to use this.”
The research team wanted to find an easy way to measure eye pressure for management of glaucoma, a group of diseases that damage the eye’s optic nerve and can cause blindness.
Right now there are two ways to check eye pressure, but both require a visit to the ophthalmologist. At most, patients at risk for glaucoma may only get their pressure checked several times a year, says Tueng Shen, a collaborator and professor of ophthalmology.
But if ophthalmologists could insert a pressure monitoring system in the eye with an artificial lens during cataract surgery—now a common procedure performed on 3 million to 4 million people each year to remove blurry vision or glare caused by a hazy lens—that could save patients from a second surgery and essentially make their replacement lens “smarter” and more functional.
“The implementation of the monitoring device has to be well-suited clinically and must be designed to be simple and reliable,” Shen says. “We want every surgeon who does cataract surgeries to be able to use this.”
As reported in the Journal of Micromechanics and Microengineering, researchers built a prototype that uses radio frequency for wireless power and data transfer. A thin, circular antenna spans the perimeter of the device—roughly tracing a person’s iris—and harnesses enough energy from the surrounding field to power a small pressure sensor chip. The chip communicates with a close-by receiver about any shifts in frequency, which signify a change in pressure.
Actual pressure is then calculated and those changes are tracked and recorded in real-time.
The chip’s processing mechanism is actually very simple, leaving the computational heavy lifting to the nearby receiver, which could be a handheld device or possibly built into a smartphone, Böhringer says.
Changing eye pressure
The current prototype is larger than it would need to be to fit into an artificial lens, but the research team is confident it can be downscaled through more engineering. The team has successfully tested the sensing device embedded in the same flexible silicon material that’s used to create artificial lenses in cataract surgeries.
Similar to how a person’s blood pressure varies throughout the day with activity levels, eye pressure is thought to behave similarly, changing perhaps minute by minute. If the pressure in the eye is too high for the optic nerve to function, however, damage to the eye can begin, often with no pain or warning signs. This increased intraocular pressure is the main factor in glaucoma, which causes vision loss and ultimately blindness.
“Oftentimes damage to vision is noticed late in the game, and we can’t treat patients effectively by the time they are diagnosed with glaucoma,” Shen says. “Or, if medications are given, there’s no consistent way to check their effectiveness.” As a result, many patients with the disease aren’t diagnosed early enough or aren’t on an accurate treatment plan.
Both cataracts and glaucoma affect a similar aging population so it seems a natural pairing to place a pressure monitoring device in a new lens during cataract surgery.
Making it cost-effective
The team is working on downscaling the prototype to be tested in an actual artificial lens. Designing a final product that’s affordable for patients is the ultimate goal, Shen says.
“I think if the cost is reasonable and if the new device offers information that’s not measureable by current technology, patients and surgeons would be really eager to adopt it.”
The researchers, including Brian Otis, associate professor of electrical engineering and also of Google Inc., and former doctoral students Cagdas Varel and Yi-Chun Shih, have filed patents on the pressure-monitoring device prototype.
University of Washington and the Coulter Foundation funded the project.
This article originally appeared on Futurity on 17 June 2014.
Header Photo Credit: Werwin15/Flickr